Call (503) 354-4094 for a free walkthrough
Mikesell Construction
Boise home with custom sunburst decorative gable woodwork and new charcoal shingles

Project Spotlight

Custom siding with decorative gable trim, Boise ID

Boise, ID

and replacement

Full tear-off

garage gable detail

Custom sunburst

across all gables

Tudor trim

This Boise project started with new siding and grew into something the homeowners had been thinking about for years. Once the decision to re-side was made, the conversation turned to the gable ends. Both the garage and the main house had plain gable faces that had always seemed like a missed opportunity. Adding custom decorative trim to those gables while the house was already under active work made sense. Christian handled the full exterior: new siding across the house, the sunburst design on the garage gable, Tudor-style trim on the main house gables, and the paint scheme that ties all of it together.

The two parts of the project, the siding and the decorative trim, are separate skill sets. Siding installation is production work: consistent layout, tight joints, correct flashing at every window and corner. Decorative trim work is craft: laying out a pattern that has never existed before on this specific gable, cutting every miter to a unique angle, building something from scratch that looks like it was always part of the house. Doing both on the same project requires shifting between the two modes of work without letting one suffer while the other gets attention.

The new siding

The siding is sage green horizontal lap installed over new house wrap across the full exterior. Lap siding installation is detail-intensive in ways that are not always visible but matter in the long run. Every window opening required new casing, properly flashed at the head and sealed at the jambs. Corner boards were set plumb and square before the field siding went in, because a corner that is out of plumb telegraphs across every course of siding that meets it. The reveals, the exposed face of each siding course below the one above it, were laid out with chalk lines at every course rather than using the previous course as a reference. Over a long wall, that discipline is what keeps the siding running true.

The material choice for lap siding on a Boise home has to account for the climate. Temperature swings from summer to winter in the Treasure Valley are substantial, and siding that is not properly back-primed before installation will absorb moisture at the cut ends and fail at the paint within a few years. Every board was back-primed before it went on the wall. The paint system on top is a full prime-and-two-coat exterior finish that will hold up through Boise winters without peeling or cracking at the lap joints.

The sage green reads differently at different times of day. In direct afternoon sun it is vivid and saturated. In morning shadow it is a muted, warm gray-green. Against the surrounding landscaping it grounds the house in a way the previous color did not. The choice was the homeowners' and it was the right one for this neighborhood and this lot.

The garage sunburst

The garage gable was the piece of this project that required the most planning before a single board was cut. A sunburst is one of the oldest decorative gable treatments in American residential architecture. The concept is straightforward: a half-circle center piece at the base of the gable with boards radiating outward from it like spokes, filling the triangular field above. The execution is not straightforward. Every spoke is a unique length. Every spoke terminates at the rake board at a different angle. The hub is a three-dimensional curved form that has to be built, not sourced off a shelf.

Christian built the hub first. A half-circle of the correct radius to anchor the design proportionally within this specific gable. The radius is determined by the gable width and height, not by a standard dimension. Too small and the hub looks like an afterthought at the base of the gable. Too large and it crowds the spokes and makes the whole piece feel heavy. The radius here was calculated to leave consistent visual weight between the hub, the spokes, and the open field at the gable edges.

Once the hub was set, the spoke layout was established. The spokes radiate from the center of the hub arc, which means every angle is derived from the same origin point. The number of spokes was determined by the spacing between them: too many and the spokes crowd at the hub, too few and the design looks sparse at the gable edges. Each spoke was cut to its finished length with the exact angle at the hub end and the exact angle at the rake end, dry-fit against the hub and the gable edge, adjusted if needed, and then installed. There is no template for this work. Every spoke is cut and fit individually.

The paint makes the sunburst work as a visual element from the street. The spokes and hub are mint green, the gable field behind them is white, and the outer edge of the gable frame is black trim. The three-color scheme gives the design contrast and depth. The mint against white creates the main visual statement. The black edge anchors the design to the rake boards and prevents it from floating visually against the sky. Getting the paint lines clean where the mint meets the white requires masking each spoke individually and holding tight edges throughout. Sloppy transitions in a sunburst design are visible from a block away.

Tudor trim on the main house gables

The main house gables were treated with Tudor-style decorative trim, a different discipline from the sunburst. Tudor trim is a flat application of boards to the face of a gable that references the exposed structural framing of traditional English timber-frame buildings. The boards create a pattern of diagonal, vertical, and horizontal elements that subdivide the gable face into panels. On this house, the pattern is a herringbone diagonal arrangement with a center vertical member and horizontal elements dividing the gable into upper and lower sections.

Tudor trim on a triangular gable is harder than it looks because the gable is not rectangular. The boards maintain consistent spacing across the face, but every diagonal board terminates at a different point along the rake as you move from the eave toward the peak. The angles at the rake are not constant. The miter at the bottom of each diagonal board, where it meets the eave trim, is a different angle than the miter at the top of the same board where it meets the rake. Every intersection is its own geometry problem.

Christian laid out the full Tudor pattern in chalk lines on the gable face before the first board was cut. This step is what separates a clean pattern from one that crowds at the peak or leaves awkward gaps at the eave. The chalk layout lets you see the full pattern, adjust spacing as needed, and verify that every termination angle is workable before committing to cuts. Once the layout was set, boards were cut one at a time, each piece fit to its specific position in the pattern before the next was started.

The paint on the main house gables matches the logic of the garage sunburst: white field, mint green trim boards, black rake edges. The consistency between the two structures is intentional. A garage with a sunburst and a house with Tudor trim in the same three-color scheme read as a coordinated exterior rather than two separate design ideas applied to the same property. When both are in the same palette, the property has a point of view.

What makes decorative gable work different

Decorative gable work is not something most siding contractors offer. It requires pattern layout skills, the patience to cut and fit every board individually to a unique angle, and the ability to execute a multi-color paint scheme cleanly across intersecting profiles. The sunburst alone involves a custom-formed hub and a dozen individually cut spokes. The Tudor pattern on two gables involves forty or more individually mitered boards. This is not work you can hand off to someone who has not done it before.

The homeowners were involved in the design decisions as the work progressed. The scale of the sunburst hub, the number of spokes, the density of the Tudor board pattern on the house gables: all of those were worked out with input from the owners rather than handed to them as finished decisions. That back-and-forth is how you end up with a result that feels like it belongs to the house rather than a design imposed on it.

How the finished exterior reads

New siding alone changes a house. New siding in a well-chosen color on a house in good condition delivers real curb appeal improvement in a straightforward way. Adding custom gable trim to a re-siding project takes significantly more time and skill, but the result is categorically different from a standard re-siding. The house has features that other houses on the street do not have. The sunburst on the garage is visible from a block away. The Tudor pattern on the house gables rewards a closer look.

Before the project, it was a solid Boise home with plain siding and blank gable faces. After, it is a home that clearly had thought and craft put into it. The functional part, the new siding and the waterproofing at every window and corner, is invisible. The decorative part is what people see from the street.

Licensed in Idaho (RCE# 43451) and Oregon (CCB# 205935). If you are re-siding a Boise home and want to add something distinctive to the exterior at the same time, call or text Christian at (503) 354-4094.

The story behind this project

  1. 1

    Siding removal

    Old siding removed across the full exterior. Sheathing inspected for moisture damage and repaired where needed.

  2. 2

    House wrap and prep

    New house wrap installed. All window casings replaced. Boards back-primed before installation.

  3. 3

    Siding installation

    Sage green horizontal lap siding installed with chalk-line layout on every course. Corner boards and trim set first.

  4. 4

    Gable trim layout

    Sunburst pattern laid out on garage gable. Tudor diagonal board pattern laid out in chalk on main house gables.

  5. 5

    Trim build and install

    Sunburst hub formed and spokes cut individually to length and angle. Tudor boards mitered and installed one at a time.

  6. 6

    Paint and finish

    Mint green, white, and black paint scheme applied to both gables. Masking and edge work done by hand at every spoke and trim board.

Project gallery

Front exterior wide view with new roof and decorative gable trim

Front exterior with driveway view

Garage gable with custom sunburst decorative woodwork and sage green siding

Custom sunburst gable woodwork

Closeup of garage decorative woodwork and charcoal architectural shingles

Gable woodwork and shingle detail